0769-23388351
Toggle Navigation
There are many kinds of magnetization methods for magnets, and there are also many kinds of magnetization waveforms, such as sine wave and square wave. Today I will tell you which magnetization waveform is sine wave or square wave.
Which is better, Magnet magnetized sine wave or square wave
Like the square wave, it is mainly suitable for occasions where the motor mainly outputs torque, such as power tools.
The sine wave is mainly suitable for the occasions that require the motor to run smoothly and have low noise, such as stepping motors.
The difference between magnet square wave and sine wave
If the magnet is charged into a square wave, the back electromotive force of the motor may be a square wave or a sine wave. If the magnet is charged into a sine wave, the back electromotive force of the motor is mostly a sine wave. Therefore, the magnetizing waveform of the magnet depends on the use occasion and driving mode of the motor. The back EMF is a sine wave suitable for sine wave driving, and the back EMF is a square wave suitable for square wave driving. The power density of a motor driven by a square wave will vary. It is larger than a motor driven by a sine wave, that is, under the same volume, a motor driven by a square wave is more powerful than a motor driven by a sine wave, but the torque output of a square wave motor is less smooth and suitable for power use. The smooth torque output of the wave motor is suitable for servo applications.
The above is an introduction to the magnet magnetization problem, whether the magnetization waveform is a sine wave or a square wave. The information comes from the Internet and is compiled and edited by Courage Magnet Xiaofu.
More on magnetization of magnets;
Can the axially magnetized magnet be demagnetized for radial magnetization?
Several common magnetization methods of multipole ring magnets
You are now seeing the specifications of this magnet ring OD 13mm, bore diameter 8mm, thickness of 3.5mm, the surface of the black epoxy, due to the reason of the photo may look like a ferrite, the actual bonded ring magnets, suitable for a variety of types of motor, sensor, and electric appliances....
Neodymium iron boron is divided into sintering, bonding and injection molding according to the different production processes. The general neodymium arc magnet is sintered, also called sintered arc neodymium magnet. Today this product is a bonded arc magnet that is not much used. The difference between sintered arc magnets is that bonded NdFeB magnet tiles require molds to produce....
Courage magnet manufacturers in China specialize in the production of various specifications of NdFeB strong magnetic tiles, large-radian strong magnetic tiles, large-sized arc magnetic tiles, arc-shaped sector magnets, and you are welcome to consult the arc-shaped magnets for quotation and proofing....
You are now browsing this ring for bonded neodymium magnets, gray epoxy on the surface, outer diameter 8mm, diameter of the hole is 4.5mm, height 6mm, it's mainly used in the field of electric motors, if you need other specifications, please consult us....
The sample shows a chemical nickel coated NdFeB small cylindrical magnet with N42 grade of magnetic properties, requires magnet N pole scribe marking, 2mm diameter, 2mm thickness, axial magnetization, the difference with conventional nickel is not obvious from the appearance but it is more suitable for use in wet, acidic or alkaline environments....
This is a small and thin (flat) round countersunk magnet, diameter 8mm, thickness is only 2mm, you see the countersunk hole neodymium magnets are generally about 3mm thick, so it belongs to the thinner countersunk hole magnets, if you want to be thinner it is difficult to process, for the customization of this type of magnets we are very good at,...
N42SH grade radial hollow cylindrical magnet 6.3x3x11mm for high speed motors...
This product is a T-shaped strong magnet, the material is rare earth NdFeB, it is a custom-shaped irregular Nd magnet, the sample is N52 grade, the surface is nickel coated, mainly used for connectors, electronic products, medical equipment, the maximum working temperature It is 80 degrees Celsius. If you need to use it in a high temperature environment, you need to replace the temperature resistant material....