0769-23388351
Toggle Navigation
We are no stranger to magnets, widely used in various industries, including cell phones, bluetooth headsets, automobiles, robots, motors, sensors, and many other products, in some application scenarios may need to customize the processing of magnets, such as punching holes, that punching holes in magnets will cause what consequences? The following will be introduced to you from the perspective of magnet manufacturers and individuals.
For magnet manufacturers, it is relatively easy to need to punch holes in magnets, because there is a full range of processing equipment and skilled workers, whether it is countersunk holes or screw holes, small holes or large holes, it is not a problem, you can see that there are a lot of holes with holes in a variety of shapes of ceramic magnets, neodymium magnets, samarium cobalt magnets in our website.
Rectangular neodymium magnets with a countersunk hole in the center
For individuals, the need to punch holes in magnets is more difficult to do successfully and carries some safety risks.
Magnets, especially neodymium-iron-boron powerful magnets, have strong magnetic force, but at the same time, they are also relatively fragile, and unsuitable tools and improper techniques can easily crack and shatter when subjected to force.
Then again, the precision cannot be controlled to meet the assembly requirements and may also produce internal cracks. Coated magnets destroy the coating are also susceptible to oxidation and corrosion, affecting longevity.
Many people may think that punching magnets is a simple DIY job, but in reality, this operation requires specialized tools and skills. Without mastering the right method, individuals may bring harm to themselves by punching holes. For example, when handling magnets, the magnets will suddenly jump due to the strong magnetic attraction, which may smash your fingers or other body parts. Also, magnet fragments or sharp edges may pose a risk of cuts.
Therefore, it is best to directly purchase or customize magnets with holes that meet the requirements, and it is not recommended for individuals to just punch further holes in the magnets they buy.
Relevant samples of magnets with holes;
Introduction to related magnet processing;
Neodymium round magnets with a diameter of 5mm and a thickness of 4mm are more commonly used. If you feel that the magnetic force is not enough, the performance level can be appropriately improved. Welcome to consult the price!...
Our company is a permanent magnet supplier from China. We are good at processing micro-precision magnets, high-performance magnets, special-shaped magnets, and multi-pole ring magnets. The quality is guaranteed and the price is not expensive. We look forward to customer consultation from all over the world....
The sample is an N52 high-performance ultra small hole radially sintered neodymium rotor magnet, with specifications of 2mm outer diameter, 0.9mm bore, and 4.5mm height....
This is a square neodymium magnet for earphones, the length and width are 5mm, the thickness is 2mm, the thickness is magnetized, the surface is galvanized, 1mm or other thickness can also be selected, non-high temperature grade, the maximum working temperature is less than 80 ℃...
The sample is a high-performance ferrite rotor magnet with a radial 3-pair pole configuration (6 poles), measuring 20mm in outer diameter, center bore diameter of 8mm, and height of 27mm. surface magnetic flux density reaches approximately 1800 Gauss....
This is a small-sized short bar shaped neodymium iron boron strong magnet with a specification of 1.5 × 1.5 × 10mm. It is made of N42 performance grade neodymium iron boron material and magnetized along the length direction (10 mm direction)....
This is a rare earth NdFeB strong magnet with a length of 30mm, a width of 20mm and a thickness of 10mm. Surface treatment is nickel-copper-nickel, and the thickness is 10mm. Magnetization direction is length direction....
This product is a small rare earth NdFeB magnet ring, with gold plated surface, N52 grade, the magnetization method is axial, the size is 5mm outer diameter, 2mm inner hole, 2mm height, and the tolerance can be ±0.02mm. Welcome to consult us for the price....