0769-23388351

Are AlNiCo Magnets Considered Strong Magnets?

Addtime:2025-07-08 09:32:15 Click:1052

Are AlNiCo magnets strong magnets? Are you curious? Today, the permanent magnet supplier Courage is here to tell you about it.


At present, among the magnet materials used on the market, the most magnetic ones are NdFeB magnets, which can withstand up to about 220°, followed by samarium cobalt, which can withstand temperatures up to 350 degrees. AlNiCo and ferrites are very magnetic. Weak, not strong magnetic, but the temperature resistance is quite good. This is also a law of magnets, magnetic force and temperature resistance are inversely proportional.

AlNiCo magnets


Comparison with ferrite: AlNiCo has much higher remanence and magnetic energy product than ferrite (ceramic magnets), making it a stronger magnet.


Comparison with samarium cobalt: Samarium cobalt outperforms aluminum-nickel-cobalt in terms of magnetic energy product and coercivity at room temperature, and it also has excellent temperature resistance (up to 300-350°C), but it is more expensive.


Comparison with neodymium-iron-boron: Neodymium-iron-boron has the highest magnetic energy product and coercivity today, making it the strongest “magnetic king” at room temperature. However, its fatal weakness is poor high-temperature performance (typically operating below 180°C, with high-temperature grades also below 230°C), and it is prone to demagnetization and corrosion at high temperatures.


Comparison with its historical status: Before the advent of rare earth permanent magnets (samarium cobalt, neodymium iron boron), aluminum nickel cobalt was the undisputed “magnetic king,” representing the strongest permanent magnets humanity could produce.


Summary: Aluminum-nickel-cobalt alloys undoubtedly belong to the traditional category of strong magnetic materials. They have written a glorious chapter in the history of permanent magnet materials, and with their high remanence and especially outstanding high-temperature stability and reliability, they continue to play an irreplaceable role in critical fields with high-temperature and high-reliability requirements. Although it has been surpassed in absolute magnetic performance by rare earth magnets such as neodymium-iron-boron, AlNiCo's stable performance under specific operating conditions makes it an indispensable “high-temperature strong magnetic guardian” in the permanent magnet material library.


See more magnet FAQs: https://www.dgcourage.com/zhishi/


Super magnet products;

Rare earth ndfeb magnets

MAGNET PRODUCT RECOMMENDATION

Tiny Ferrite Magnet Block Length magnetization 1x1x2.45mm

This is a very small rectangular ferrite block magnet, measuring 2.45 mm in length and 1 mm in both width and height. It is magnetised along its length and is barely noticeable when held in the hand....

Small Ceramic Ferrite Block Magnet 7.4mm x 6mm x 5mm

7.4x6x5mm Ferrite Small Block Magnet Introduction,Material: Hard Ferrite (Ceramic),Shape: Block / Rectangle / Bar,Coating: No Coating,Grade (Chinese Stardard): Y30,Operating temperature: -40°C to 250°C,Delivery time: 7-15 days,Magnetization direction: thickness....

U shaped ndfeb magnets in the shape of the letter U

U-shaped neodymium magnets are a type of high-performance permanent magnet material with a structure resembling the letter ‘U’. Manufactured from sintered neodymium-iron-boron, they are characterised by high magnetic energy product....

4 pole bonded ndfeb ring rotor magnet 16 x 5 x 20 mm

This is a radial 4-pole ring (Hollow cylinder) magnet, the material is bonded NdFeB, with high magnetic performance, the size is 16mm outer diameter, inner hole 5mm, height 20mm, surface gray epoxy treatment, suitable for water pump motor...

4 pole ring Injection magnet for pushrod motors 22 x 7 x 4 mm

This product is a 4-pole ring magnet, injection-molded ferrite material, the sample size is 22mm outer diameter, 7mm inner diameter, 4mm thickness, 2 N poles and 2 S poles, mainly used for push rod motors, magnetic induction devices, encoders, etc.,...

Encoder radial 2-pole circular magnet 6x2.5 10x2.5 N35

This is a radial 2 pole circular magnet designed specifically for magnetic encoder chips. It is made of sintered neodymium-iron-boron with N35 grade performance and is suitable for standard environments....

1.5mm small inner hole multipole injection ferrite magnet ring

This product is a multi pole magnetic ring with an inner diameter of 1.5mm. The material is injection molded ferrite. It adopts axial multi pole magnetization and is mainly used for DC motors. If you have a sample of similar injection molded magnetic products, please contact us for quotation....

Tiny block neodymium magnet with zinc coating 1.5mm x 1.5mm x 3mm

This is a very small size rectangular block magnet with galvanized surface, 3mm length, 1.5mm width and height, with very fine tolerance, magnetized by lengthwise direction, mainly used in precision electronics, instrumentation, please contact us if you need to buy....

WHAT ARE YOU STILL HESITATING? CONTACT US NOW!

CONTACT NOW