As we all know, there are two kinds of magnets, natural and artificial, which have strong magnetism. But it has spontaneous magnetization. Therefore, the preservation of strong neodymium magnet is particularly important. How to storing the magnet for a long time? Today, courage magnet is here to share with you the strong magnet preservation skills. What should be paid attention to when storing the strong magnet?
How to security store neodymium magnets?
1, ndfeb magnet do not close to the electronic equipment, because the magnet itself has a positive and negative electrode, there is a circuit circuit, close to the influence of electronic equipment and control circuit and affect the use of.
2. Do not store the magnet in a humid environment to avoid oxidation, which may cause changes in appearance, physical properties and magnetic properties.
3, don't put magnets near a floppy disk, hard disk drives, credit CARDS, tapes, record card, TV picture tube, etc. If magnets are placed near devices such as magnetic recorders, the recording data can be affected or even destroyed.
4, Never store or use magnets above their Curie temperature (590°F for Neodymium magnets) to avoid demagnetization.
5, Because the magnetic force is too strong, need to do a good job of magnetic isolation.
6, Keep out of reach of children and pets or lock them if necessary.
7, When placing magnets in the storage box, always make sure they are tightly snuggled with padding (paper, Styrofoam, bubble wraps etc.) in all around, with no room for the magnets to move around. For large sized magnets, always place thick spacer in between every two magnets for stress-free separation.
8, Do not stack it directly on the ground, it is recommended to pad it with cardboard or place it on a shelf.

If properly preserved, it can maintain magnetism for a long time. If you want to avoid weakening the magnetism of the magnet, you should pay attention to the following aspects:
1. Do not put the magnet around the strong current;
2. The magnet can't be baked on the fire and can't stand the high temperature;
3. The magnet shall not be knocked or vibrated violently;
4. Small magnets cannot be put together with large magnets;
PS: you should always be very careful when storing the magnet, because the magnet will stick together by itself and may hurt your fingers. It is also possible that the magnets themselves may be damaged by collision when they are adsorbed on each other (collision of corners or cracks).
These are some precautions for magnet storage. Whether you are a factory or an individual, it is worth seeing.
Relevant neodymium magnet knowledge;
Maximum working temperature and Curie temperature of neodymium magnet
This is a very small rectangular ferrite block magnet, measuring 2.45 mm in length and 1 mm in both width and height. It is magnetised along its length and is barely noticeable when held in the hand....
7.4x6x5mm Ferrite Small Block Magnet Introduction,Material: Hard Ferrite (Ceramic),Shape: Block / Rectangle / Bar,Coating: No Coating,Grade (Chinese Stardard): Y30,Operating temperature: -40°C to 250°C,Delivery time: 7-15 days,Magnetization direction: thickness....
U-shaped neodymium magnets are a type of high-performance permanent magnet material with a structure resembling the letter ‘U’. Manufactured from sintered neodymium-iron-boron, they are characterised by high magnetic energy product....
This is a radial 4-pole ring (Hollow cylinder) magnet, the material is bonded NdFeB, with high magnetic performance, the size is 16mm outer diameter, inner hole 5mm, height 20mm, surface gray epoxy treatment, suitable for water pump motor...
This product is a 4-pole ring magnet, injection-molded ferrite material, the sample size is 22mm outer diameter, 7mm inner diameter, 4mm thickness, 2 N poles and 2 S poles, mainly used for push rod motors, magnetic induction devices, encoders, etc.,...
This is a radial 2 pole circular magnet designed specifically for magnetic encoder chips. It is made of sintered neodymium-iron-boron with N35 grade performance and is suitable for standard environments....
This product is a multi pole magnetic ring with an inner diameter of 1.5mm. The material is injection molded ferrite. It adopts axial multi pole magnetization and is mainly used for DC motors. If you have a sample of similar injection molded magnetic products, please contact us for quotation....
This is a very small size rectangular block magnet with galvanized surface, 3mm length, 1.5mm width and height, with very fine tolerance, magnetized by lengthwise direction, mainly used in precision electronics, instrumentation, please contact us if you need to buy....